PA12 LX9008

 

VESTAMID® LX9008
聚酰胺12

Evonik Degussa GmbH  
    
 Technical Data   
    

产品说明

High-viscosity, plasticizer-free extrusion compound with an extraordinary longterm heat resistance

VESTAMID LX9008 is a plasticizer-free polyamide 12 compound, with an especially high long-term resistance under thermal load.

VESTAMID LX9008 is suitable to produce flexible tubes that are permanently exposed to higher temperatures, e.g., in the engine compartment of motor vehicles. Especially when used as diesel fuel lines they show significant advantages compared with standard grades, obvious in storage tests

with diesel fuel (see the figure).

The material absorbs only little moisture, thus leading to nearly unaffected dimensions and properties of the finished parts at changing ambient conditions.

Using VESTAMID LX9008 for fuel lines one must pay attention to certain preconditions. The Technical Marketing Department gives you advice in selecting the suitable VESTAMID compound.

总体

 材料状态 • 已商用:当前有效   
 资料 1 •  Technical Datasheet (English)
  
 Search for UL Yellow Card •  VESTAMID®
  
 供货地区 • 北美洲 • 欧洲  
 添加剂 • 冲击调节器 • 热稳定剂  
 性能特点 • 尺寸稳定性良好 • 吸潮性差  
  • 良好的耐热老化性能 • 粘度,高  
     
 用途 • 管道 • 燃料管线  
 形式 • 颗粒料   
 加工方法 • 挤出   
     
 物理性能  额定值 单位制 测试方法 
 密度  1.01g/cm³ ISO 1183 
 吸水率   ISO 62 
 饱和, 23°C  1.6%  
 平衡, 23°C, 1.00 mm, 50% RH  0.70%  
 机械性能  额定值 单位制 测试方法 
 拉伸模量  1450MPa ISO 527-2 
 拉伸应力   ISO 527-2 
 屈服  42.0MPa  
 断裂  50.0MPa  
 拉伸应变 (屈服)  5.0% ISO 527-2 
 断张率  > 150% ISO 527-2 
 冲击性能  额定值 单位制 测试方法 
 简支梁缺口冲击强度   ISO 179/1eA 
 -30°C, 完全断裂  22kJ/m²  
 23°C, 局部断裂  45kJ/m²  
 23°C, 完全断裂  45kJ/m²  
 简支梁缺口冲击强度   ISO 179/1eU 
 -30°C  无断裂  
 23°C  无断裂  
 悬壁梁缺口冲击强度 3 (-40°C)  无断裂 SAE J844 
    SAE J2260 
 Impact Strength   ISO 7628/2 
-- 4  No BreakJ  
 23°C 5  No Break  
1 / 3    
 
VESTAMID® LX9008
聚酰胺12
Evonik Degussa GmbH   
      
  热性能 额定值 单位制 测试方法 
     
  熔融温度 6 176°C ISO 11357-3 
  补充信息 额定值 单位制 测试方法 
  Hoop Stress - at Burst  DIN 53758 
  23°C 44.0MPa   
  60°C 20.4MPa   
  100°C 13.2MPa   
  120°C 11.1MPa   
  140°C 8.70MPa   

备注
1 通过这些链接您能够访问供应商资料。我们尽量保证及时更新资料;不过您可以从供应商处了解最新资料。

2 一般属性:这些不能被视为规格。

3 tubing 8x1mm, after 24h /110°C

4 tubing 8x1mm, as molded

5 tubing 8x1mm, 72h/ 150°C

6 DSC, 2nd Heating

 

PA12 TR90副牌料,PA12 TR90原料,PA12 TR90水口料,PA12 TR90改性料,PA12 TR90眼镜料,电话0769-87795123
版权所有:东莞市双帮塑胶原料有限公司    网址:http://www.pa12tr90.com/
粤ICP备12050428号-3